Geekcreit® DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter With Receiver

Geekcreit® DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter With Receiver
  • Sellerparentingasdkids.com
  • List PriceUS$5.39piece
  • Sale PriceUS$5.39piece
  • ShippingFree Shipping
  • Ratings4,9 (689)

Product Description

Feature:
Material: Plastic + Metal
RF Frequency: 433Mhz
Standby Current: <8.5MA
Receive sensitivity: >97 dBm
Wiring type: Fixed terminal
RF working mode: Superheterodyne
Transmitting distance: More than 15 meters
Decoding mode: MCU software decoding
Learnable transmitters: 1-16 transmitters
Support remote type: Learning code (1527)
Switching modes: Both Momentary & Toggle
Switch output: Normally open & normally closed
Wire Port:
NO: Normal open
COM: Common
NC: Normal close
Momentary Mode:
Push the remote button, the relay activates, release the remote button the relay deactivates.
Toggle Mode:
Push and release the remote button, the relay activates.
Push and release the remote button again and the relay deactivates.
Clearing All Stored Transmitters:
(Note: After clearing the stored transmitters, all transmitters will need to be relearned by the receiver.)
Push the learning button on the receiver 8 times, and the codes will be cleared .
Learning the transmitter: ( Momentary Mode )
Programming a 2 button transmitter as momentary mode transmitter.
STEP 1
- Push and release the learning key on the receiver ONCE.
- Wait for a moment, the LED will turn off, indicating you entered the learning state.
STEP 2
- Push and release the first button on your transmitter, the LED on the receiver board will flash on then off indicating the button was learned.
STEP 3
- Press and release the second button, watching the LED go on and off again.
- Wait 3 seconds, the LED will turn on again, indicating system is ready for use.
Learning the transmitter: ( Toggle Mode )
- Programming a 2 button transmitter as a toggle.
STEP 1
- Press and release the learning key on the receiver TWICE.
- Wait for a moment, the LED will turn off, indicating you entered the learning state.
STEP 2
- Press and release the first button on your transmitter, the LED on the receiver board will flash on then turn off.
- Indicating the button was learned.
STEP 3
- Next press and release the second button, watching the LED go on and off again.
- Wait 3 seconds, the LED indicator will turn on again, indicating system is ready for use
Package included:
1 x Receiver Module
2 x Remote Control (Battery included)
Notes:
1. Two-button transmitters can only be used as toggle or momentary.
2. You let the control panel to learn the remote control, you must press the "A" and "B" button; Rather than just pressing one of them. However, you can program another transmitter in the other mode.
3. Manual measuring, please allow 1 ~ 3mm error, thank you.
4. Due to the difference between different monitors, the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the picture.


220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

220V 2CH RF Wireless Remote Control Switch Relay Receiver Module Transmitter

Similar Products